Workstation with a curved monitor showing an orange screen, plants on wall shelves and a mesh chair
Implementing Hybrid Work

How do I measure the utilisation of our office space reliably?

Saskia
18.11.2026
11
min
Workstation with a curved monitor showing an orange screen, plants on wall shelves and a mesh chair

You measure office utilisation reliably if you define the metrics in advance, combine at least two data sources, measure over several representative weeks, cross-check the results with on-site spot checks and involve data protection and the works council from the outset.

The lease at the headquarters expires in eighteen months. By the autumn, Real Estate is expected to say whether the space will be renewed, reduced or merged with a second office. Three figures are on the table, and none of them matches the others: the booking tool reports high utilisation, access control counts significantly fewer people, and on a walk-through the office looks full on Tuesday and almost empty on Friday. Anyone who makes a space decision on this basis risks ending up with too much space or too little. For Real Estate, Facility and Workplace Management in companies with hybrid working, the point is therefore not yet another figure, but a measurement of office usage that can be trusted.

This guide shows you which metrics count for the space decision, what the individual data sources deliver and where they stop, how to build a measurement plan in six steps and what to consider regarding data protection and the works council.

Why utilisation figures contradict each other

Almost every unreliable utilisation figure can be traced back to one of five sources of error. If you know the problem, you can set up the measurement so that it does not occur.

Booking is not the same as presence

Desk booking and room booking show intentions, not reality. Booking data only shows planned presence, not actual usage. If an employee reserves a desk on the third floor the evening before and then spontaneously works from home the next morning, the desk remains marked as occupied all day. Desk booking systems allow employees to book workstations or meeting rooms in advance; on their own, they usually do not show whether the booking was actually used.

No-shows and early departures

Workstations that are booked but not used make office utilisation appear higher than it is. If a team reserves ten desks every Tuesday but only six people regularly turn up, four empty workstations flow into the reports as occupied. Some systems therefore rely on a check-in at the desk, which, however, is only as good as the discipline of its users. Without a check-in or a comparison with presence data, no-shows remain invisible.

Average instead of peak

A low quarterly average utilisation sounds like potential savings. But if the office is full on Tuesdays and Wednesdays and almost empty on Fridays, the average says nothing about the real need for space. Space decisions depend on whether there are enough workstations on the busiest days.

Holidays and special periods

School holidays, bridge days, the summer lull or year-end business change usage considerably. If these periods are not marked, they distort long-term data in both directions. A measurement period in the middle of the summer holidays is no basis for a decision on leased space.

Different definitions per location

Location A counts a desk as occupied as soon as personal belongings are left there. Location B only counts it as occupied once someone has been present for at least two hours. Different rules make cross-location statements worthless, especially in companies with many offices. Metrics, definitions and calculation logic should therefore be defined and documented before the measurement starts.

The most important metrics for the space decision

Before you select tools or decide on a method, you need clarity about the metrics your decision is based on. These metrics should be collected regularly to measure office space utilisation. Renew, reduce or consolidate: each option needs different data.

MetricFormulaWhat it is useful for
Occupancy rateworkstations actually used on a day ÷ available workstationsassessing how much space is really used
Booking rateworkstations or rooms reserved on a day ÷ available workstations or roomsrecognising demand and planning intentions
No-show rateworkstations booked but not used ÷ workstations bookeduncovering overestimation from booking data
Peak utilisationhighest number of workstations used simultaneously in the period ÷ available capacitysizing leased space for the busiest days
Utilisation per areaoccupancy of a floor or zone ÷ capacity of that arearecognising differences, justifying refurbishments

Utilisation is calculated as the percentage of occupied workstations. A fictitious example shows why the distinction matters: with 100 workstations, 60 are reserved and 45 are used. The booking rate is 60 per cent, the occupancy rate 45 per cent. The difference is explained by no-shows, spontaneous changes or work at another location.

The most important planning figure for leased space is peak utilisation; utilisation per area is the basis for targeted refurbishments. If quiet zones are rarely used and team areas are overbooked, this argues for a redistribution within the building, for example in favour of space for collaboration.

Data sources at a glance: what each method shows and where it stops

There is no perfect single source for measuring office utilisation. Each method covers a different part of the picture; meaningful insight only comes from combining the data. For reliable measurements, a combined approach using several methods is therefore recommended.

Data sourceWhat it showsLimitationsEffort
Booking data from desk booking and room bookingworkstations and rooms reserved per dayplanned usage only, no statement about actual presence or spontaneous usagelow, if a booking system is in place
Access and badge datapeople who have entered the buildingonly show who has entered the building, not which workstation or area was usedlow, existing infrastructure
Manual counts and spot checksactual occupancy at a point in time, including through belongings left behindsnapshot, labour intensivemedium, counting rounds by the facility team
Network-based presencedevices active on the office network or Wi-Fi, at floor or location levela device is not the same as a person, no accuracy at workstation levellow to medium, existing network
Presence sensors on desks or ceilingsphysical presence at the workstation via movement or heatpurchase, installation, maintenance; usually subject to co-determinationhigh, dedicated hardware and maintenance work
Software for recording presenceconnects bookings with presence data, shows patterns over timeas good as the connected sourcesmedium, introduction and configuration

Booking data is important for operational management, but should not support a lease decision on its own. Access and badge data shows how full a building is, but not how the office space within it is used. Network-based methods evaluate how many devices are active in the office; together with software that connects booking and presence, they often close the gap between plan and reality. Hardware at individual workstations can make sense where accuracy at desk level is really needed; the costs of installation and maintenance must then be justified.

The accuracy you need depends on the decision: for a question about leased space, accuracy at floor level is usually sufficient, but not for the detailed planning of individual zones. It is best to define this requirement before you collect data.

The measurement plan: six steps to robust figures

Metrics, period and data sources combine into a measurement plan before a lease is renewed or space is given up.

  1. Name the decision. Formulate the question that is to be answered, for example: “Will we still need all three floors after the lease ends?” For a reduction, peak utilisation per floor and the no-show rate are decisive; for a consolidation, utilisation per area across all locations.
  2. Define a representative period. Measure over several weeks covering all days of the week. Mark holiday and special weeks so that they remain visible but do not distort the overall picture. For major decisions, it is worth looking at several periods during the year.
  3. Combine sources. Connect at least two sources: booking data for planned usage, network-based presence for actual attendance, manual counts as a control.
  4. Check plausibility on site. Carry out counting rounds on typical peak days and compare each count with the reports from booking and presence. If the values differ significantly, look for the cause before you continue measuring.
  5. Evaluate by location, floor, area and day of the week. Project areas, focus zones and communal areas often have completely different patterns. Peaks on Tuesday and Wednesday affect the decision about the building differently from an even weekly pattern.
  6. Involve data protection and the works council. Clarify purpose, scope of data and retention periods before the first measurement runs. More on this in the next section.

It is best to document each step so that colleagues from finance can also follow the evaluation later.

Data protection and co-determination: trust as part of data quality

A measurement that the workforce distrusts delivers poorer data: workstations are not booked as a precaution, devices stay off the network. Data protection is therefore not just an obligation but part of reliability, and for many companies the most important issue before the start.

The GDPR requires purpose limitation and data minimisation. Booking data is personal data and should be anonymised and aggregated for evaluations; aggregated data is the key to a data protection compliant measurement. Access data is legally more sensitive than it appears, because it is often assigned to individual people.

Technical equipment that is suitable for monitoring behaviour or performance is subject to co-determination by the works council under Section 87(1) No. 6 of the German Works Constitution Act (BetrVG). According to the case law of the Federal Labour Court, what matters is the objective suitability for monitoring, not the intention (BAG, decision of 13 December 2016, 1 ABR 7/15). Hardware at the workstation therefore usually requires a works agreement. How to involve data protection and the works council in the data collection step by step is described in our guide to GDPR compliant measurement of office utilisation. This content does not replace legal advice; we recommend a legal review of the individual case.

“Isn't our booking data enough?” What the answer means for Real Estate

Many companies have been using desk booking for years, and the dashboard with booked workstations is ready. The short answer: booking data is necessary, but on its own it is not sufficient for a decision on reducing or consolidating space.

A booking reflects neither the length of the stay nor the actual work at the workstation. Anyone who leaves for an external appointment at eleven o'clock and does not return counts as present in the system all day. Even a small share of no-shows leads to noticeable deviations as soon as Real Estate derives workstation numbers from it.

Only linking bookings and presence shows which bookings were actually used. Patterns then also become visible, for example teams with many no-shows or areas that are used spontaneously without a booking. Reliable observation of space usage is crucial with hybrid working, because office attendance fluctuates strongly from day to day.

Questions to ask usage analysis tools

Before you select software, these questions help to distinguish reliable usage analysis tools from mere dashboards and to classify what the solutions can do:

  • Is data aggregated and evaluated without reference to individuals? Reports at space, zone or location level are sufficient for Real Estate and make it easier to reach agreement with the works council.
  • Can several locations and companies be mapped? Without consistent levels, utilisation cannot be compared between offices.
  • Are comparisons across periods and scenarios possible? This is the only way to show whether an optimisation of the space has worked.
  • Are there exports for the business case? Metrics and usage information often end up in separate models for rent and operating costs.
  • Does the solution fit into Microsoft 365? Deep integration with Microsoft 365 can make the management of office space more efficient, because booking and evaluation take place in employees' everyday work without switching between systems.
  • Do bookings and presence come together? The real strength of a platform for utilisation analysis lies in connecting the sources, not in individual charts.

How Seatti delivers a robust picture of usage

To this day, many space decisions are based on booking statistics and the impression from a walk-through. What is missing is the actual picture of usage: a booking dashboard shows what employees intend to do, but Real Estate also needs to know what really happens in the office in order to decide on space and operating costs. That is why we built Seatti so that Workspace Management and Office Intelligence work together in one system.

With Workspace Management, employees reserve workstations, meeting rooms, parking spaces and services directly in their familiar environment, in Microsoft Teams and Outlook. You manage companies, locations and rule sets centrally via enterprise structures with granular roles and permissions.

Office Intelligence brings together bookings, IP-based presence and existing infrastructure into a picture of usage that shows utilisation, patterns by day of the week and savings potential per location. IP-based presence detects attendance automatically via the existing network infrastructure, without an additional check-in, and only records the network login: without location tracking and without movement profiles. It is included in Intelligence Essentials, Seatti Signals are part of Intelligence Pro, and full usage analysis is part of Intelligence Enterprise. You can find more about IP-based presence on our website.

For data protection and co-determination, the following applies: hosting and data processing in the EU, pseudonymised and aggregated usage data, no live monitoring, no geolocation, no working time recording, anonymous booking possible, ISO 27001 certified. Seatti is built to make co-determination easier. You can find details on our page on data protection and data security.

Client case: how bonprix turned measurements into a new space

How much a reliable measurement is worth is shown by bonprix. After the redesign of its Hamburg campus for hybrid working, it turned out that the pilot areas were used much less often than planned, and nobody knew reliably who was in the office when. bonprix chose Seatti because the solution is easy to use and creates transparency about presence and space usage. Based on the usage data and at the request of employees, an area planned as a quiet zone was completely redesigned.

The figures from twelve months (September 2025 to August 2026): 54,000+ planned office days and 66% higher utilisation per workstation than in the previous year. The path there did not lead via a single metric, but via the question of which areas work and where space should be used differently.

Conclusion: from measurement to space decision

From the usage data, Real Estate builds the logic for the business case. The analysis starts with peak utilisation per location and ends with scenarios including costs.

From peak utilisation to the desk sharing ratio

Peak utilisation is translated into space requirements: how many workstations are actually needed on the busiest days? Comparing this with the number of employees gives the desk sharing ratio, which you use to calculate scenarios.

Scenarios and costs

Underused zones can be played through in scenarios: terminating partial areas, merging locations or repurposing rooms. You model cleaning, energy and facility operations along these scenarios; current usage data can also help to adapt energy and services to actual demand. Measuring office utilisation thus helps to cut costs and plan space requirements appropriately, and office space that matches usage also benefits employee satisfaction.

In front of management, you present utilisation charts and scenarios side by side. Robust figures rather than gut feeling decide whether a space decision holds up or has to be corrected later.

Would you like to see how Seatti runs in your Microsoft 365 environment? In a 30-minute walkthrough, we show how Seatti simplifies your office processes and puts your space decisions on a data-driven footing.

Book a demo now

Read more: Calculating space requirements per employee and Measuring office utilisation in compliance with the GDPR.

Author and sources

Author: Saskia Neuner, Chief of Staff at Seatti. As of 18 November 2026.

Sources:

Frequently asked questions

How do you measure office utilisation most reliably?

The most reliable approach is a combination of booking data, presence data, for example network-based, and on-site spot checks. Measure over a sufficiently long period with clearly defined metrics and evaluate at space level. A single data source does not provide a robust picture of utilisation.

How long should utilisation be measured?

A period of several weeks that covers all days of the week and marks special days makes sense. Before major decisions such as reducing space at the headquarters, you should look at several periods during the year to identify seasonal fluctuations.

What is the difference between booking rate and occupancy rate?

The booking rate is based on reserved workstations, the occupancy rate on workstations actually used. The booking rate often overestimates usage, especially when there are many no-shows. For space decisions, the occupancy rate is the more robust metric.

Can office utilisation be measured in compliance with the GDPR?

Yes, if the purpose is clearly defined, evaluations are anonymised and aggregated, retention periods are limited and the works council is involved. A legal review of the individual case is advisable, as the requirements differ depending on the method.

Which software is suitable for recording presence in the office?

Suitable solutions connect presence data with bookings, support several locations, evaluate in aggregated form without reference to individuals and fit into the existing IT. Seatti works natively in Microsoft 365 and connects bookings with IP-based presence.

Enjoyed this article? Share it with a colleague.
Our mission at Seatti is to make hybrid work smarter and more efficient. By connecting people, workplaces, and real-time utilization data, we help companies create better office experiences and make smarter decisions about their spaces.
Saskia
Table of contents
Table of contents
See Seatti for yourself

An interactive tour of booking, presence and space utilisation. No appointment needed, right in your browser.

Your personal live demo

Get to know Seatti! We work out the potential for your company in around 30 minutes.